Buying titanium is not one decision. It is five: which grade, which form, which specification, which certificate, and how much. Get any one wrong and you either over-specify — paying aerospace prices for a part that only needed general corrosion resistance — or under-specify and watch it fail in service. This page is a buying hub. It gives you a short answer to each of the five questions, then a mapped route to our detailed guides on grades, plate, tube, bar, fittings, price, certification and supply from Baoji. Every link goes to a live page on this site. Start with the question you actually have, not with a catalogue.
How to use this page. This is a navigation hub, not a material-data sheet. It does not invent a single grade, price or allowable stress. Each number, limit and standard lives on the linked detail page with its own source and boundary. Where sources conflict — maximum service temperature, minimum bend radius,-grade equivalence — the linked guides print the conflict instead of a convenient single value.
Almost every titanium enquiry reduces to the same five questions. Answer them in this order and the rest of the purchase — grade, spec, price, certificate, supplier — falls into place. Skip one and you will pay for it later in a re-order or a failed part.
Grade is chosen by the medium and the load, not by habit. The table below is a starting point; the linked guides give the chemistry, mechanicals and the failure boundaries.
| If your duty is | Usual starting grade | Why | Read next |
|---|---|---|---|
| Seawater, brine, general chloride | Grade 2 (CP titanium) | Self-healing TiO₂ film, best cost balance | Grade 2 vs Grade 7 |
| Hot reducing acid, stagnant crevice | Grade 7 or Grade 12 | Pd or Mo stabilises the film where Gr2 cannot | Gr12 plate guide |
| Structural strength, load bearing | Grade 5 (Ti-6Al-4V) | Roughly three times CP strength | Gr5 bar stock |
| Medical implant, aerospace ELI | Grade 23 (Ti-6Al-4V ELI) | Lower interstitial limits, toughness at low temperature | Gr5 vs Gr23 guide |
| Caustic soda, high temperature alkali | Nickel 200 / 201, not titanium | Nickel resists hot caustic; titanium does not | Nickel product guide |
| Acetic acid, aggressive reducing media | Zirconium 702, not always titanium | ZrO₂ film stays stable where TiO₂ may break | Titanium vs zirconium |
Go deeper: Grade 2 vs Grade 5 selection, ASTM / GB / EN grade equivalence, Gr5 vs Gr23 and Gr2 vs Gr7 in seawater. For a full buying walkthrough, see how to buy titanium from China.
Form decides the specification, the price basis and the lead time. Plate and sheet are quoted by thickness and area, tube by outside diameter and wall, bar by diameter and length. These are the forms we hold in stock in Baoji and cut to size.
Start with Titanium Plate, Grade 2 plate to ASTM B265 or the ASTM B265 sheet, strip and plate guide. If you already know the duty, the buy-by-end-use plate guide matches grade and thickness to chemical, marine and medical service, and cut-to-size plate covers zero-cut orders. Current stock sizes are on the Gr1 / Gr2 / Gr5 stock page. Convert thickness to mass with the titanium weight chart.
The tube specification is ASTM B338 for titanium tube and B861/B862 for pipe. The B338 ordering-by-failure-mode guide is the fastest way to avoid a wrong wall or weld choice. For service-specific builds see U-bent condenser tube, condenser tube supply and the welded vs seamless selection guide.
Bar to ASTM B348 is the strength product. Grade 5 bar stock covers the common aerospace and fastener grade; the chip and dust safety guide explains why machining it needs a different shop discipline than plate. Spring and welding wire have their own specifications — name the wire form, not just the alloy, on the RFQ.
Small components are where a correct material choice most often goes wrong. A fitting to ASTM B363, a flange to ASME B16.5 / B165 and a fastener to the F468 / F467 series each carry their own grade, marking and inspection requirements. Because these parts are small, heat-number transfer and material traceability matter more here than anywhere else.
A supplier who only sells titanium will try to solve every problem with titanium. Honest selection sometimes means a different metal. Nickel 200, Ni201 and Monel 400 handle hot caustic and reducing conditions that attack titanium; the Ni200 vs Ni201 guide explains the carbon limit. Titanium vs zirconium in acetic acid shows where a ZrO₂ film survives and a TiO₂ film does not. Our ready-stock page lists titanium, nickel and zirconium together so one enquiry can cover all three.
For a titanium heat exchanger, a shell-and-tube unit for brine or lithium extraction, a coil, a reactor or an agitator, the material is only half the specification. The joint design, weld argon shielding, hydrotest and code stamp decide whether it survives. Read the equipment buyer’s guide before you release a drawing.
Two quotes for “Titanium Plate” are rarely for the same thing. The specification name, its edition, the delivery condition and the inspection level change both the price and what you are legally entitled to reject. Line these four up before you compare numbers.
| Line on the quote | Why it changes the answer | What to write |
|---|---|---|
| Specification and edition | Chemistry and tolerance limits move between editions | ASTM B265-2022, not just ‘B265’ |
| Delivery condition | Annealed, cold-worked or STA have different strength and formability | State the temper or condition |
| Surface and tolerance | Pickled, bright or polished; thickness tolerance class | Name finish and tolerance class |
| Certificate and inspection | 3.1 vs 3.2, with or without witnessed tests and UT | EN 10204 level and NDT scope |
The ASTM B265 guide and annealed vs STA guide explain the spec and condition side. Equivalent grades across ASTM, GB and EN are in the equivalence guide — names alone are not proof of the same material.
Per-kg titanium quotes differ because the underlying scope differs. The five drivers below are the ones to line up before comparing suppliers.
| Driver | Effect on price | What to state on the RFQ |
|---|---|---|
| Grade and chemistry | Pd-bearing Gr7 costs more than CP Gr2 | Exact grade or UNS number |
| Form and thickness | Thin sheet and tight tolerance cost more per kg | Thickness, width, length, tolerance |
| Specification and certificate | Aerospace spec and 3.2 inspection add cost | Spec, edition, EN 10204 level |
| Quantity and cutting | Small cut-to-size lots cost more per kg than mill lots | Fixed sizes and cut list |
| Market and lead time | Sponge titanium moves; rush stock carries a premium | Target delivery date |
Read why titanium quotes differ per kg, the price page, a worked 6 mm Gr2 sheet price and the Gr2 flange price example. Prices move with the market — treat published figures as indicative and confirm on the day.
EN 10204 3.1 mill certificates should name the UNS number, ASTM specification and edition, heat number, chemistry and mechanical results. For pressure, aerospace or medical work add PMI and heat-number transfer on every cut piece. Our traceability and PMI guide explains why a magnet and a spark test cannot verify a grade, and our certifications page lists what we can supply. Certificate and metal must agree — ask for both.
Once grade and form are right, four questions still decide whether the part lasts: how it is loaded, how hot it runs, how it is formed, and what the medium really does. These are the guides we send when a buyer asks “will titanium survive this?”
| Question | Guide | What it prevents |
|---|---|---|
| Will it crack under repeated load? | Fatigue and surface integrity | Buying a high grade but leaving a bad machined surface |
| How hot can it run? | Maximum service temperature | Confusing oxidation, strength, creep and code limits |
| Can it be bent or formed cold? | Forming and bend radius | Using an ASTM ductility value as a die radius |
| Will a pump or pipe wear out? | Cavitation and erosion | Assuming corrosion resistance equals wear resistance |
| Can stress plus medium crack it? | Stress corrosion cracking | Ignoring residual stress in methanol or hot chloride |
| Do the chips create a fire hazard? | Titanium fire and dust safety | Reaching for water on burning titanium chips |
| Does a magnet verify the grade? | Magnetic properties and MRI | Accepting a wrong alloy on a visual check |
| How many melts do I need? | Double vs triple VAR | Paying for a melt claim without a spec to back it |
Follow the relevant link: fatigue, service temperature, forming and bending, cavitation and erosion, stress corrosion cracking, fire safety, magnetic properties and melt practice. For a real failure map, see the dry chlorine and HCl corrosion casebook. Heat treatment and its oxide layer are in the annealed vs STA guide.
Copy the twelve lines below into your enquiry. The more you fill in, the fewer rounds of questions you will have.
| # | Field | Example or note |
|---|---|---|
| 1 | Grade or medium | Gr2, or ‘seawater, 35 ppt, 30 °C’ |
| 2 | Product form | Plate, tube, bar, fitting, flange, fastener |
| 3 | Dimensions | Thickness / OD / wall / length / width |
| 4 | Specification and edition | ASTM B265-2022, ASME SB338, etc. |
| 5 | Quantity and cut list | Fixed sizes, zero-cut, number of pieces |
| 6 | Certificate level | EN 10204 3.1 or 3.2, PMI required? |
| 7 | Heat-number transfer | Required on each cut piece? |
| 8 | Service temperature and pressure | Normal and upset conditions |
| 9 | Inspection | UT, PT, RT, hydrotest, dimensional report |
| 10 | Destination and Incoterms 2020 | Write full rule and named city, e.g. FOB Ningbo |
| 11 | Target delivery date | Stock vs made-to-order |
| 12 | Consequence class | Pressure, safety-critical, or general — who reviews |
Send the checklist through our inquiry page. If you are new to sourcing from China, the buy-from-China guide covers supplier checks, Incoterms and the documents to expect.
Choose Grade 2 if your duty is general chloride or seawater corrosion and you want the best cost balance. Choose Grade 7 or 12 if the medium is hot reducing acid or a stagnant crevice. Choose Grade 5 if you need structural strength. Choose Grade 23 if it is medical or aerospace ELI. Choose nickel or zirconium if the medium is hot caustic or aggressive reducing acid where titanium is the wrong film.
Buy from stock if a standard size fits and you need days, not weeks. Buy cut-to-size if you want to avoid waste and a mill minimum — just make sure the heat number travels with every piece. Buy certified if the part is pressure, safety or aerospace critical; the certificate and the metal must both check out.
Start at the top of this page with the five questions, follow one link for the answer you need, then send the twelve-line RFQ. That is the shortest path from “I think I need titanium” to a quote you can actually compare.
Start with the medium and the duty, not the grade name. For general chloride and seawater corrosion, Grade 2 is the default; for hot reducing acid, Grade 7 or Grade 12; for structural strength, Grade 5; for medical or aerospace ELI, Grade 23. Our grade selection guide and ASTM/GB/EN equivalence guide compare them side by side. Send the medium, temperature and concentration and the supplier should confirm the grade.
There is no single price. Per-kg cost moves with grade, form and thickness, specification and certification level, order quantity, and the current sponge-titanium market. Grade 7 carries palladium and costs more than Grade 2; a certified aerospace heat costs more than general stock. Our why-prices-differ guide breaks down each driver, and our price pages show current levels. For a real number, send size, grade, spec and quantity to the supplier.
At minimum an EN 10204 3.1 mill test certificate naming the UNS number, the ASTM specification and edition, the heat number, chemistry and mechanical results. For traceability-critical work, add positive material identification and heat-number transfer on every cut piece. A certificate proves what the paperwork says; PMI checks what the metal actually is. Both are covered in our traceability and mill-certificate guides.
Yes. As a stockholder and light fabricator we cut to size with no mill minimum — one plate, one spool or a small kitted line is a normal order. That is exactly why the specification and certificate matter: once a certified plate is cut, the heat number has to be transferred to every piece. Say the finished size you need, not the mill size, when you ask for a quote.
It depends on the medium. Titanium wins in chloride and seawater service where 316L pits, and in many oxidizing acids; it is a poor choice in hydrofluoric acid and in dry chlorine, and it is softer and more prone to galling than steel. Compare by medium, not by reputation — our corrosion casebook and grade-versus guides print the boundaries on both sides.
Six things: grade (or the medium if you do not know it), product form and dimensions, specification and edition, quantity and whether cut-to-size is needed, certificate and inspection requirements, and destination port or Incoterms 2020 city. Add the service temperature and whether the part is pressure or safety critical. The RFQ checklist near the end of this page is copy-ready.
Baoji is the centre of China’s titanium industry, so stock range, cut-to-size service and price competition are strong. Check four things: that the mill certificate and heat number match the material, that the spec and edition are named, that the Incoterms 2020 rule and destination are written in full, and that the supplier confirms lead time against real stock. Our buy-from-China guide works through each step, including DFARS and tariff questions to raise with your own contracts team.
Need a Quote? Message Us Directly
Get live stock status, price and lead time — usually the same business day. No form required, just tap to chat.
Контактное лицо: Wang Xiaoning
Телефон: +86-917-355-7966
Эл. почта: [email protected]
WhatsApp: +86 188 2967 9311
Компания: Shaanxi Qianyi Tuoda Technology Co., Ltd
Адрес: Floor 4, Building 4, No. 188 Gaoxin Avenue, High-tech Zone, Baoji City, Shaanxi Province, China