Welcome to Shaanxi Qianyi Tuoda Technology Co., Ltd
EnglishРусский中文
Titanium Metal News

Titanium Weight Calculator: Plate, Tube, Bar Charts & 5 Costly Mistakes

Titanium Plate, bar and tube are sold by the kilogram, so the weight on the quotation is a commercial number before it is a technical one. The arithmetic is simple: CP titanium is 4.51 g/cm³, Ti-6Al-4V (Grade 5) is 4.43 g/cm³, and Ti-3Al-2.5V (Grade 9) is 4.48 g/cm³. From those three densities, a 3.0 mm Grade 2 plate weighs 13.53 kg/m², a 20 mm Grade 2 bar weighs about 1.41 kg/m, and a 25.4 × 2.0 mm tube weighs about 0.66 kg/m. The expensive mistakes are rarely in the multiplication. They are in using one density for every grade, mixing millimetres and metres, ignoring thickness tolerance, and letting a supplier invoice theoretical weight when the contract says weighed — or the reverse. Boundary: every figure below is a theoretical weight at nominal dimensions and nominal density. Hot-rolled tolerance, grade chemistry and actual measured thickness move the real mass. Use these charts to budget and to check a quote; for settlement weight, use the method written into your contract and the scale weight on the packing list. See our grade equivalence guide for why two grades with similar names can carry different chemistry.

How to read the charts. We are a stockholder and light fabricator in Baoji, not a standards body. Densities and chart values below are published producer/reference figures, reproduced with the source named in the field table; they are theoretical values at nominal size, not certified shipping weights. The factor 0.982 converts a CP-titanium figure to Grade 5 because 4.43 ÷ 4.51 ≈ 0.982; Grade 9 uses 4.48 ÷ 4.51 ≈ 0.993. Always confirm the density basis and the weight-settlement method on your own purchase order. If a number decides a shipment cost, ask us or your supplier to calculate from your exact dimensions and grade before the order is placed.

At a Glance: Nine Numbers That Decide a Titanium Weight Quote

Factor Value Applies to What to freeze on the RFQ
CP Ti density 4.51 g/cm³ Gr1/2/3/7/12 Name the grade, not just “titanium”
Grade 5 density 4.43 g/cm³ (0.982× CP) Ti-6Al-4V, Gr23 Use the alloy factor or the chart drifts 2%
Grade 9 density 4.48 g/cm³ (0.993× CP) Ti-3Al-2.5V Small, but not zero on a big order
Plate per m² Thickness(mm) × 4.51 kg CP basis Full sheet = T × W × L × 4.51 ÷ 106
3.0 mm plate 13.53 kg/m² CP; Gr5 ≈ 13.28 Budget freight per sheet
Bar per metre d²(mm) × 0.00354 kg/m CP round bar / wire Diameter squared, not diameter
20 mm bar ~1.415 kg/m CP; Gr5 ≈ 1.39 Multiply by cut length
Tube per metre (OD − wall) × wall × 0.01414 CP, seamless or welded Wall thickness drives the number
25.4 × 2.0 tube ~0.662 kg/m CP tube Confirm OD and wall from the drawing

How to use this table: every row is a field that changes the number on an invoice. A supplier who confirms all nine is quoting the same material you are costing. For why two quotes can differ beyond weight, see our quote-comparison guide.

1. The Short Answer: Three Densities, Three Formulas

Every titanium weight calculation is density times volume. The only complications are which density belongs to your grade and which unit convention the formula assumes. Commercially pure grades sit at 4.51 g/cm³, Grade 5 and Grade 23 at 4.43, and Grade 9 at 4.48. Plate uses area times thickness, bar uses diameter squared, and tube uses wall thickness times the difference between outer diameter and wall.

Keep the formulas on this page in millimetres and kilograms, and convert only at the end. If you prefer an interactive tool, our plate weight calculator, tube weight calculator and bar weight calculator pages run the same arithmetic. This article exists so the numbers are visible, checkable and indexable without scripts.

2. Density by Grade: Why “Titanium” Is Not One Number

Most buyers use 4.51 for everything and are only slightly wrong most of the time. The error becomes commercial when the order is large or the alloy is Grade 5. The table gives the published values and the factor to apply to a CP-titanium figure.

Grade Type Density g/cm³ Factor vs CP Typical use
Grade 1 / 2 / 3 Commercially pure 4.51 1.000 Plate, tube, vessels, piping
Grade 7 CP + Pd 4.51 1.000 Hot chlorides, reducing acids
Grade 12 Ti-0.3Mo-0.8Ni 4.51 1.000 Crevice service, cost-saving Gr7 option
Grade 5 Ti-6Al-4V 4.43 0.982 High-strength parts, aerospace
Grade 23 Ti-6Al-4V ELI 4.43 0.982 Medical, cryogenic toughness
Grade 9 Ti-3Al-2.5V 4.48 0.993 Tubing, springs, weld wire

The factors are simple ratios: 4.43 ÷ 4.51 ≈ 0.982 and 4.48 ÷ 4.51 ≈ 0.993. Our ASTM / GB / EN equivalence guide explains why grade names alone can mislead; the same care applies to the density you put in a costing sheet.

3. Plate Weight: Per Square Metre and Per Full Sheet

For commercially pure titanium, weight per square metre equals thickness in millimetres times 4.51. For a full sheet, multiply thickness, width and length in millimetres by 0.00000451. A 6 mm plate 1500 mm wide and 3000 mm long is 6 × 1500 × 3000 × 0.00000451 = 121.77 kg.

That is the number to use for freight planning and for a first check of a supplier’s quote. It is not the number to use for settlement unless your contract says theoretical weight. The Grade 2 plate page and plate overview list the stock sizes that these charts are based on.

4. Titanium Plate Weight Chart (CP Basis, 4×8 ft Sheet)

The chart uses a 4 × 8 ft sheet area of 2.973 m². Grade 5 column applies the 0.982 factor. Values are theoretical at nominal thickness.

Thickness mm kg/m² CP 4×8 ft sheet, CP kg 4×8 ft sheet, Gr5 kg
0.5 2.26 6.70 6.58
0.8 3.61 10.71 10.52
1.0 4.51 13.39 13.15
1.5 6.77 20.10 19.73
2.0 9.02 26.78 26.30
3.0 13.53 40.18 39.46
4.0 18.04 53.56 52.60
5.0 22.55 66.95 65.75
6.0 27.06 80.34 78.90
8.0 36.08 107.12 105.20
10.0 45.10 133.94 131.49
12.0 54.12 160.69 157.79
15.0 67.65 200.86 197.24
20.0 90.20 267.86 262.98

Use the middle column for a quick freight number and the last column when the material is Ti-6Al-4V. Thicker gauges are normally hot-rolled and carry a larger thickness tolerance, so the scale weight may sit below the theoretical column. Our plate specification quick-lookup table lists the common size combinations in stock.

The fastest way to get an exact weight back from every supplier is to send the same dimension fields to all of them. Copy these lines into your enquiry.

What to send us for an exact titanium quote

Copy these nine lines into your enquiry. A complete spec means a firm price on the first reply, not a second email asking for the grade.

Spec item Example from a real order
Grade Grade 2 (UNS R50400), commercially pure titanium
Standard ASTM B265 / ASME SB-265, current revision
Form & Size Plate, 6 mm × 1000 mm × 2000 mm, hot-rolled and annealed
Quantity 500 kg (12 sheets), one-off batch
Service medium & temperature Seawater, 30 °C, continuous immersion
MTC type EN 10204 3.1, heat-specific, with melt chemistry and tensile values
Inspection Third-party witness (SGS / BV) before dispatch; PMI on request
Target delivery Ex-works within 5 working days; FOB Shanghai on request
Drawing DXF of cut-to-size blanks, tolerance ±1.0 mm, edges deburred

Ready? Copy the nine lines above into the Requirement Details box on our Request a Quotation page and we will come back with a firm price and a dispatch date within 24 hours.

5. The “4.51 for Everything” Mistake

A 2,000 kg Grade 5 order costed at 4.51 instead of 4.43 is overstated by roughly 36 kg. At a titanium price per kilogram that is a real number, and it grows with every tonne. The error is invisible on a single small piece, which is why it survives from one quotation to the next.

The fix is to name the grade in the costing sheet, not just the material family. If a supplier quotes a weight without asking which grade, they have assumed one for you. Compare the answer against the alloy column before you accept it, and read our Grade 5 plate page if the order is high-strength material.

6. Bar and Wire Weight: Diameter Squared, Not Diameter

For commercially pure round bar and wire, weight per metre equals diameter in millimetres squared times 0.00354. The square is the part people forget: doubling the diameter quadruples the weight per metre. A 20 mm bar is about 1.415 kg/m; a 40 mm bar is about 5.659 kg/m, not 2.83.

ø mm CP kg/m Gr5 kg/m ø mm CP kg/m Gr5 kg/m
6 0.127 0.125 50 8.843 8.686
8 0.226 0.222 60 12.73 12.50
10 0.354 0.348 80 22.64 22.23
12 0.509 0.500 100 35.37 34.73
15 0.796 0.782 150 79.58 78.14
20 1.415 1.389 200 141.48 138.93
25 2.211 2.171 — — —
30 3.183 3.126 — — —
40 5.659 5.557 — — —

Multiply the per-metre figure by the cut length to get piece weight. The same expression covers round titanium wire; the alloy factor covers Grade 5 spring and aerospace stock. For a bar order with a specified length and tolerance, our Grade 5 bar stock page shows the forms we hold.

7. Tube and Pipe Weight: Wall Thickness Does the Work

For commercially pure tube, weight per metre equals (outer diameter minus wall) times wall times 0.01414. The expression works for both seamless and welded product because it calculates the metal cross-section, not the bore. A 25.4 × 2.0 mm tube is about 0.662 kg/m; a 114 × 4.0 mm tube is about 6.222 kg/m.

OD × wall, mm CP kg/m Gr5 kg/m
25.4 × 1.2 0.411 0.404
25.4 × 1.65 0.554 0.544
25.4 × 2.0 0.662 0.650
38 × 1.5 0.775 0.761
38 × 2.0 1.018 0.999
57 × 2.0 1.555 1.527
57 × 3.0 2.291 2.250
60.3 × 2.0 1.647 1.617
89 × 3.0 3.648 3.582
114 × 3.0 4.708 4.623
114 × 4.0 6.222 6.110

For sizes outside the chart, apply the formula rather than interpolating by eye. Our welded versus seamless selection guide explains when the process matters more than the arithmetic, and the published price report carries the same charts beside current market prices.

8. The Five Mistakes That Turn an Estimate into a Wrong Invoice

Most weight disputes are not arithmetic disputes. They are disagreements about which number the contract uses. These five are the ones we see repeatedly on enquiries and delivery documents.

Mistake What happens Commercial effect Control
1. One density for all grades Using 4.51 for Grade 5 ~2% high: 40 kg on a 2,000 kg order Use 0.982 factor or the Gr5 column
2. Millimetres treated as metres Mixing mm dimensions with an m-based formula 1,000× error Use the mm formulas on this page verbatim
3. Ignoring thickness tolerance Hot-rolled plate under nominal gauge Theoretical weight exceeds scale weight Agree nominal vs measured thickness in the PO
4. Theoretical vs weighed not stated Invoice basis left undefined Dispute at delivery, delayed payment Write the settlement method into the contract
5. Using OD × wall for tube Treating tube like a solid bar Large overestimate of mass and freight Use (OD − wall) × wall × 0.01414

The fourth row is the one worth slowing down for. “Theoretical weight” and “scale weight” are both legitimate, but they are not the same clause. If your purchase order is silent, the two sides will discover the difference at delivery. Write the settlement basis next to the quantity, every time.

9. Worked Example: Ten Sheets of 6 mm Grade 2 Plate

Take ten sheets of Grade 2 plate, 6 mm thick, 1500 mm wide and 3000 mm long. Per sheet: 6 × 1500 × 3000 × 0.00000451 = 121.77 kg. Ten sheets = 1,217.7 kg theoretical. At Grade 5 the same ten sheets would be about 1,195.8 kg after the 0.982 factor.

Those are the numbers for a freight quote and a budget. Before the order is confirmed, check the mill tolerance on thickness: if the delivered gauge averages 5.9 mm, the scale figure is roughly 17 kg lower across the ten sheets. None of this changes the price per kilogram, but it changes the total on the invoice and the space in a container. Our cut-to-size service works from nominal stock sizes and states the basis before cutting.

10. Theoretical Weight vs Weighed Weight

Theoretical weight is calculated from nominal dimensions and nominal density. Weighed weight is what the calibrated scale reads on the packed goods. Both are used in titanium trade, and neither is universally correct.

Theoretical is convenient for cut pieces, mixed lots and fast quoting. Weighed is preferred when thickness tolerance could move the mass materially or when both parties want a single undisputed number at delivery. State which one applies, and if it is weighed, state whose scale governs and whether the certificate lists net or gross. A clear mill certificate and packing list remove most of the argument.

11. The Unit Traps: Millimetres, Metres and Pounds

The formulas on this page take millimetres and return kilograms. Using the same numbers as metres produces a result a thousand times too small; mixing a metre-based formula with millimetre inputs produces one a thousand times too large. Pick one convention and write it next to the calculation.

Export orders add a second trap: kilograms versus pounds. One kilogram is 2.205 pounds. If a US buyer is costing in lb and a Chinese mill quotes in kg, the two spreadsheets will disagree by a factor of 2.205 until someone states the unit. This is the same discipline we apply to Incoterms wording in the China sourcing guide.

If you would rather not do the arithmetic, send the grade, dimensions and quantity through our request a quotation page. A named engineer will return the calculated weight, the settlement basis and the stock position in writing — within 24 hours — so you can compare suppliers on one number.

12. Where a Weight Chart Is the Wrong Tool

Charts are for budgeting, checking a quote and planning freight. There are orders where they stop being useful, and saying so is part of a straight answer.

Situation Why the chart is not enough What to do instead
Freight and container planning Charts are good enough to budget Confirm with nominal dimensions and grade
Custom cut or forged shape No chart row matches your part Calculate from volume × density, or ask us
Contract settlement Theoretical is not the invoiced basis Use the method written into your PO
Cold-drawn vs hot-rolled tolerance Actual gauge shifts the real mass Measure representative pieces, agree tolerance
Nickel or zirconium order Different density entirely Use the nickel chart or ask for the basis
Strength or corrosion decision Weight does not answer the service question Start from the grade and failure guides

Nickel and zirconium use different densities again; our nickel plate weight calculator covers the nickel family. If the real question is which grade survives the medium, start with the failure casebook or the fatigue guide rather than a weight table.

13. A Twelve-Line Weight RFQ Checklist

Send these fields together and every supplier returns a weight on the same basis. The most important lines are 3, 6 and 7: dimensions, tolerance and settlement method.

# Field Example entry
1 Grade and product standard Gr2 ASTM B265 / Gr5 ASTM B348
2 Density basis 4.51 CP / 4.43 Gr5 / 4.48 Gr9
3 Nominal dimensions Plate 6 × 1500 × 3000 mm; bar ø20; tube 25.4 × 2.0
4 Quantity and unit Number of sheets / pieces / metres
5 Product form Hot-rolled plate / cold-rolled sheet / seamless tube
6 Tolerance applied to gauge Standard ASTM tolerance or agreed special
7 Weight settlement method Theoretical by calculation, or actual scale weight
8 Scale and certificate Calibrated scale; MTC type and heat number
9 Cut size / drawing Attach DXF or state cut dimensions
10 Packing Crate / pallet, export marks, net and gross weight
11 Incoterms and destination port FOB Ningbo, Incoterms 2020
12 Quote validity and lead time Price basis date; stock vs made-to-order

Line 7 is worth repeating: theoretical or weighed, in writing, before the order. It costs one sentence and prevents the most common delivery dispute in mill-product trade. Pair this checklist with the quote-comparison guide to separate weight from the other reasons two quotes differ.

14. Why Source This From Us

We are a stockholder plus light fabricator in Baoji, the centre of China’s Titanium Valley. Weight questions are stock questions for us:

  • Calculated from your dimensions, not a guess. About 800 t of titanium, nickel and zirconium stock across plate, tube, bar, wire, fittings, flanges and fasteners means we calculate from the grade and size you actually need.
  • Settlement basis stated up front. We tell you whether the quote uses theoretical or scale weight, and what tolerance applies, before the order is placed.
  • Cut-to-size, zero-cut, no mill minimum. One plate or one spool from declared stock; net and gross packing weights on the documents.
  • The certificate carries the evidence. EN 10204 3.1 MTC per heat, measured chemistry on request, heat numbers hard-stamped; 3.2 with a named witness agreed before manufacture.
  • Fast where it counts. Weight and pricing within 24 hours, stock sizes dispatch the same day, export packing and documents handled in house.

Start with plate, tube, bar, wire, flange or fittings; each page lists the forms, sizes and tolerance options that matter for that product.

Get a firm titanium quote within 24 hours

Same-day dispatch from ~800 t of Baoji stock  ·  cut-to-size and waterjet blanks  ·  free drawing review by our engineering team  ·  EN 10204 3.1 MTC with every lot.

Request my quote →

No obligation. A named engineer replies, not an auto-responder.

EN 10204 3.1 MTC on every lot  · ISO 9001 quality system  ·  ASTM / ASME / GB standard literacy  ·  Third-party inspection (SGS / BV) on request  ·  Mill heat & lot traceability  ·  Export packing & full documentation

15. FAQ: Titanium Weight Calculation

What is the density of titanium?

Commercially pure titanium grades 1, 2, 3, 7 and 12 are normally taken as 4.51 grams per cubic centimetre. Ti-6Al-4V, grades 5 and 23, is about 4.43, and Ti-3Al-2.5V grade 9 is about 4.48. These are published reference values at nominal chemistry; your mill certificate is the authority for the material you buy.

How do I calculate Titanium Plate weight?

For commercially pure titanium, weight in kilograms equals thickness in millimetres times width in millimetres times length in millimetres times 0.00000451. For a quick figure, weight per square metre equals thickness in millimetres times 4.51. A 3 mm plate is therefore about 13.53 kilograms per square metre. For grade 5, multiply the result by 0.982.

How much does a 20 mm titanium bar weigh per metre?

For commercially pure titanium, weight per metre in kilograms equals diameter in millimetres squared times 0.00354. A 20 mm round bar is about 1.415 kilograms per metre, so a six-metre length is roughly 8.5 kilograms. Grade 5 is about 1.39 kilograms per metre at the same diameter. These are theoretical values at nominal diameter.

How is titanium tube weight calculated?

For commercially pure titanium, weight per metre in kilograms equals (outer diameter minus wall) in millimetres, times wall thickness in millimetres, times 0.01414. A 25.4 by 2.0 mm tube is about 0.662 kilograms per metre. The same expression works for seamless and welded tube; grade 5 uses the 0.982 alloy factor.

Why is my titanium weight different from the chart?

Charts assume nominal dimensions and nominal density. Hot-rolled plate can arrive under nominal gauge within the permitted tolerance, cold-drawn bar can vary slightly, and grade chemistry shifts density a little. If the difference matters commercially, agree in the purchase order whether the invoice uses theoretical calculation or actual scale weight, and check the packing list.

Does Grade 5 weigh less than Grade 2?

Yes, slightly. Grade 5 density is about 4.43 grams per cubic centimetre against 4.51 for commercially pure grades, so the same physical volume weighs about 1.8 percent less. On a small sample the difference is trivial; on a multi-tonne order it is real enough to put in the quotation. Multiply any commercially pure chart value by 0.982.

What should I send to get an exact titanium weight and quote?

Send the grade, the product standard, nominal dimensions, quantity and product form, plus whether you want theoretical or scale-weight settlement. Add your cut size or drawing and the destination port. With those fields we can return the calculated weight, the stock position and a price against our Baoji stock, usually within 24 hours.

Summary: Name the Grade and the Settlement Basis

Titanium weight is density times volume; the expensive part is choosing the right density and the right contract clause. Use 4.51 g/cm³ for commercially pure grades, 4.43 for Grade 5 and 23, and 4.48 for Grade 9. Plate is thickness times area times 4.51, bar is diameter squared times 0.00354 kg/m, and tube is (OD minus wall) times wall times 0.01414 kg/m. These are theoretical numbers for budgeting and checking quotes; agreement on theoretical versus scale weight belongs in the purchase order. Send the twelve-line checklist through our request a quotation page; a named engineer will return the calculated weight and stock position within 24 hours.

<a href=https://www.sxqytd.com/product/titanium-plate.html target='_blank'>Titanium Plate</a> stack with a caliper and a weight chart sheet on a packing bench

Need a quote on this specification?

Click below and your email app opens with the 6-point RFQ already typed out. Just fill in your grade, size and quantity - no form, no captcha.

Email your RFQ ›

Prefer the web form? Open the inquiry page and paste the 6 points into the message box.

Baoji Titanium Valley · ~800 t stock · cut-to-size · drawing-based machining · ASTM / ASME / GB · export-ready · same-day quote.