Welcome to Shaanxi Qianyi Tuoda Technology Co., Ltd
EnglishРусский中文
  • Zirconium vs Titanium: A Selection Guide
Zirconium vs Titanium: A Selection Guide

Zirconium vs Titanium: A Selection Guide

SpecificationTopic: Zirconium vs Titanium selection
Applicable StandardCovers: HCl/H2SO4 resistance, seawater, cost, temperature, ASTM
Material ConditionStandard: ASTM B551/B265, B523/B338, B493/B348, B366/B363
Inspection & PackagingService: reducing acid, chloride, pickling, chlor-alkali, cost trade-off

Product Description: Zirconium vs titanium selection guide: compare cost, corrosion in HCl/H2SO4/seawater, temperature limits and ASTM standards to choose the right metal.

Request a Quote Contact Sales

Product Overview

Zirconium vs Titanium: A Selection Guide

Choose zirconium when the fluid is a strong reducing acid — boiling hydrochloric or sulfuric acid, acetic, formic — and titanium or 316L cannot hold; choose titanium Gr2 / Gr7 for seawater, chloride and mild acid where budget leads. Zirconium resists boiling HCl at every concentration and stays intact to about 250°C in most reducing acids, but it costs roughly 8–10× titanium and is not a high-temperature metal. We stock both metals in Baoji, cut and shipped with full mill certificate, so you can split one corrosion line by fluid: zirconium for the worst reducing acid, titanium where the medium and the budget dictate. This guide gives the head-to-head, the grade map, where each metal actually fails, and a one-line rule to stop guessing.

The reason a selection guide beats a catalogue is simple: a corrosive line is plate shells, tube bundles and bar-made shafts from one grade system — specifying them consistently is what keeps a plant leak-free for decades. Below, the head-to-head, then the shared failure map and one rule. For the alloy picture across nickel, titanium and zirconium, see our materials materials coverage; if you also run nickel, our nickel hub explains the family.

At a Glance: Zirconium vs Titanium: A Selection Guide

Form / property Zirconium vs Titanium Note
Plate / sheet Zr702, Zr705 (B551)  |  Ti Gr1/2/7/12 (B265) Both in stock, cut to size
Tube / pipe Zr702/705 (B523/B658)  |  Ti Gr2/7 (B338/B862) Both in stock
Bar / rod Zr702/705 (B493)  |  Ti Gr5/2 (B348) Both in stock
Fittings / flange Zr (B366/B16.5)  |  Ti (B363/B16.5) Both machined to spec
Boiling HCl (all conc.) Zirconium: excellent  |  Titanium: fails Zirconium wins
Seawater / chloride Zirconium: OK  |  Titanium: excellent Titanium wins on cost
Max useful temp (air) Zirconium ~540°C limit  |  Titanium ~315°C Zirconium higher
Relative cost Zirconium high  |  Titanium low Titanium far cheaper

1. What 锆 vs 钛

:腐蚀工况选型指南 Actually Means

Both are reactive metals protected by a self-healing oxide film — but the films are opposites. Titanium's film is TiO₂, superb in chloride and seawater yet weak in reducing acids; zirconium's film is ZrO₂, superb in reducing acids yet weak in hydrofluoric acid and hot caustic. That single difference decides 90% of selection cases. We treat both as stock corrosion metals — titanium and zirconium planned from one grade system so the whole line stays consistent.

2. Grade Quick-Reference

Grade Composition Use it for
Zr702 (R60702) ~99.2% Zr+Hf, low O Boiling HCl/H2SO4; max formability
Zr705 (R60705) +2.5% Nb Same acids, ~50% higher strength
Gr2 (R50400) CP-Ti, low O Seawater, chloride, mild acid
Gr7 (R52400) CP-Ti + Pd Stronger reducing / crevice duty
Gr12 (R53400) Ti + Mo/Ni Moderate reducing acid, cheaper than Zr

For the full material picture — zirconium, titanium and nickel side by side — see our alloy matrix matrix. If the service is reducing acid but milder, our titanium titanium guide explains the cheaper option.

3. How to Read the RFQ

A usable quote starts with a usable request. Put these on the enquiry so we return price and lead time instead of questions:

  • Service fluid — acid, concentration, temperature, contaminants (esp. fluoride).
  • Preferred metal — zirconium or titanium, or “advise”.
  • Grade — Zr702/Zr705 or Gr2/Gr7/Gr12.
  • Form & size — plate/thickness, tube OD/wall, bar dia, qty.
  • Certificate — EN 10204 3.1 MTC with heat number.
  • Condition — annealed; tolerance class.
  • Weld prep — confirm argon backing; we supply filler.
  • Destination — port, packing (VCI / crate).

4. Forms, Sizes & What to Specify

Form Typical size Where it goes
Plate / sheet Thk 0.5–50 mm (Ti) / 0.5–50 mm (Zr) Shells, tube sheets, liners
Tube / pipe OD 6–219 mm Heat-exchanger bundles, transfer lines
Bar / rod Dia 6–300 mm Shafts, agitators, machined parts
Fittings / flange per B16.5 / B16.9 Branch, turn, termination

5. Standard & Certification You Receive

Each lot ships with an EN 10204 3.1 mill test certificate, heat-number traceable to the melt, to ASTM B551/B265 as applicable. Condition is annealed per spec; PMI, UT or dye-penetrant can be added on the order. For a mixed line we kit titanium and zirconium from one shipment with one certificate pack.

6. The “One Metal Solves Everything” Myth

Neither metal is universal. Zirconium is not a cheap drop-in for titanium, and titanium is not a substitute in boiling hydrochloric acid. Match the grade to the fluid — see our zirconium grade notes and titanium grade notes for the chemistry, and our alloy matrix when the service is neither.

7. Where Zirconium AND Titanium DO Fail — a Head-to-Head

Zirconium’s strength is its reducing-acid film; its limits sit exactly where that film breaks down. Read the failure map, then the joint notes.

Medium / condition Titanium Zirconium
Boiling HCl, all concentrations Titanium: attacked Zirconium: excellent
Reducing H2SO4, hot Titanium: marginal Zirconium: excellent
Seawater / chloride, low acid Titanium: excellent Zirconium: OK but overkill
Hydrofluoric acid / fluoride Titanium: attacked Zirconium: attacked (both fail)
Concentrated hot caustic Titanium: attacked Zirconium: attacked
Strong oxidiser (fuming HNO3, wet Cl2 + oxidiser) Titanium: attacked Zirconium: attacked
Dry chlorine Titanium: attacked Zirconium: resists
Air service above ~540°C Titanium: oxidises Zirconium: oxidises / can burn

Two joint-specific notes. Zirconium is noble when passive, so coupling it directly to a much baser metal without isolation can accelerate the partner — use a dielectric spacer where the partner is critical. And never forget fluorine: any fluoride, even trace, is an exclusion, so confirm the medium is fluoride-free before you specify zirconium.

8. Choose by Service, Not by Habit

Choose this if:

  • Boiling HCl or H2SO4 at any concentration → zirconium.
  • Acetic, formic, phosphoric (reducing), pharma-clean → zirconium.
  • You need higher strength / thinner wall at the same resistance → Zr705.
  • The medium is fluoride-free reducing acid → zirconium.

Choose that if:

  • Seawater / chloride, low acid → titanium Gr2 / Gr7 (far cheaper).
  • Mild duty or large equipment where budget leads → titanium.
  • Service contains HF or fluoride → Monel / nickel (both fail).
  • Concentrated hot caustic → Ni200 / Ni201.

9. Common Procurement Mistakes

  • Using titanium in boiling hydrochloric acid — rapid attack; use zirconium.
  • Using zirconium in hydrofluoric acid — rapid attack; use Monel.
  • Assuming zirconium is cheap — it is 8–10× titanium; use titanium where it suffices.
  • Mixing Zr702 and Zr705 (or Gr2 and Gr7) on one RFQ without stating which.
  • No MTC on a pressure part.

10. Lead Time, MOQ & Export Packing

Zirconium and titanium are held in Baoji across plate, tube, bar, wire, fittings and flange, cut to size and dispatched fast for standard sizes. Heavy-wall tube, large forged flange or special tempers lead a few weeks. Small MOQ applies — a single plate, one spool or a set of flanges is a normal order, and we kit the whole line from one shipment with one certificate pack.

11. Zirconium vs the Alternatives — When NOT to Specify Zirconium

If the service is… Then…
Mild, room-temperature, non-critical Titanium Gr2 is far cheaper and usually enough.
Seawater / chloride, low acid Titanium Gr2 / Gr7 covers most chloride duty at lower cost.
Hydrofluoric acid / fluoride Use Monel 400 / pure nickel; zirconium fails here.
Concentrated hot caustic Use Ni200 / Ni201; zirconium is attacked.
Strong oxidiser / mixed acid Step to Hastelloy C-276 / C-22; zirconium may be wrong.
High-temperature air service Inconel 600 / 625 holds; zirconium oxidises above ~540°C.
You want one metal for everything No such metal — match grade to fluid; see our matrix.

12. Welding & Joining Note

Both welds are GTAW under argon, but the bar is different. Zirconium needs argon backing gas on BOTH sides of tube and pipe or the weld turns hard and brittle; titanium needs a trailing shield on the face. Keep the joint and wire scrupulously clean — a contaminated weld is the most common field failure for either metal. We supply matching filler and a qualified WPS note.

13. Reading the Mill Test Certificate

Every lot ships with an EN 10204 3.1 EN 10204 3.1 MTC: grade and UNS, heat number, chemistry (including hafnium, which affects nuclear grade), tensile result, and the ASTM specification. Keep the heat number — it is your traceability link from the finished part back to the melt.

14. Why a Baoji Titanium-Valley Stockist

We hold titanium and zirconium together in Baoji, close to China’s Titanium Valley supply base, so we can cut, forge and kit a mixed corrosion line from one shipment instead of chasing several mills. That shortens lead time from mill-weeks to days and keeps one grade logic, one certificate pack, one point of contact. Our guide explains the stock-holder model for overseas buyers.

15. A 5-Minute RFQ Template

Copy this into your enquiry and fill the blanks — it returns a quote, not a guessing game:

  • Product: Zirconium vs Titanium: A Selection Guide, grade ___
  • Metal preference: zirconium / titanium / advise ___
  • Service: medium ___, concentration ___, temperature ___, pressure ___ (confirm fluoride-free)
  • Spec: ___ (ASTM / ASME)
  • Size: ___ ; quantity ___
  • Condition / finish: ___
  • Certificate: EN 10204 3.1, UT/PMT if needed
  • Destination & packing: port ___, VCI / crate

Email it to [email protected] — we confirm stock and pricing within 24 hours, and can kit the whole line from one Baoji shipment so grade and certificate stay consistent end to end.

16. FAQ — Zirconium vs Titanium

: A Selection Guide

When should I choose zirconium over titanium?

Choose zirconium when the medium is a strong reducing acid — especially boiling hydrochloric or sulfuric acid at all concentrations — and titanium or 316L cannot hold. For seawater, chloride and mild acid, titanium Gr2 / Gr7 is far cheaper and usually enough.

Does titanium resist hydrochloric acid?

No. Titanium is attacked by hydrochloric acid except in very dilute, cold conditions. For HCl service use zirconium (or Hastelloy / tantalum); titanium is the wrong call for boiling HCl.

Is zirconium worth the higher cost?

Yes where it is the only affordable option — zirconium resists boiling HCl at a fraction of tantalum’s cost. But for seawater or mild duty, titanium does the same job far cheaper, so do not over-specify zirconium.

What about seawater or chloride service?

Titanium Gr2 / Gr7 is the standard for seawater and most chloride duty; zirconium also resists it but costs far more for the same result. Use titanium unless the medium is also a reducing acid.

Can zirconium and titanium be used in the same system?

Yes, but mind galvanic coupling: zirconium is more noble than titanium, so the less noble partner can corrode faster if directly bonded. Isolate the two with a dielectric spacer where the partner is critical.

What welding do both metals need?

Both are GTAW under argon. Zirconium needs argon backing on both sides of the joint; titanium needs a trailing shield on the face. Either way the joint and wire must stay clean — a contaminated weld fails fast.

Do you stock both metals and export worldwide?

Yes. We hold titanium and zirconium in Baoji, cut to size, with full EN 10204 3.1 MTC and export packing, to global ports.

Summary: One Rule Beats a Catalogue

If you take one thing from this guide, take this: specify the metal for the fluid, not just the word “corrosion-resistant,” and treat every joint as a system. Zirconium vs Titanium: A Selection Guide is the right call for the right metal per service — and never specify it where the failure map says no. Send the checklist above to [email protected] or use the inquiry form — we confirm stock and pricing within 24 hours, and can kit the whole line from one Baoji shipment.

Zirconium and titanium stock side by side in Baoji Titanium Valley warehouse

Get a Free Quote

Tell us your requirement — grade, size and quantity. We reply within 24 hours.

Captcha code

Prefer chat? WhatsApp +86 188 2967 9311 or email [email protected].