| Specification | Zirconium in Hydrochloric Acid |
|---|---|
| Applicable Standard | Covers: HCl envelope, recovery units, Zr702 vs Zr705, design, failure |
| Material Condition | Standard: ASTM B551, B523, B658, B493, B366, ASME B16.5 |
| Inspection & Packaging | Service: boiling HCl, HCl recovery, pickling acid, acetic + HCl |
Product Description: Zirconium in hydrochloric acid: boiling HCl resistance, HCl recovery units, Zr702 vs Zr705, design and failure limits, ASTM B551/B523, RFQ checklist.
Zirconium is the go-to metal for hydrochloric acid: it resists boiling HCl at every concentration where titanium, 316L and most nickel alloys fail, and at a fraction of tantalum’s cost. In HCl recovery and regeneration units — pickling-line acid recovery, spargers, reheaters, crystallisers — zirconium tube and plate routinely outlast everything else. We stock Zr702 and Zr705 across plate, tube, bar, fittings and flange in Baoji, cut and shipped with full mill certificate, so your HCl loop runs for years, not months. This guide covers the concentration / temperature envelope, Zr702 vs Zr705 in HCl, equipment design, and exactly where zirconium must NOT be used.
The reason a selection guide beats a catalogue is simple: a corrosive line is plate shells, tube bundles and bar-made shafts from one grade system — specifying them consistently is what keeps a plant leak-free for decades. Below, the head-to-head, then the shared failure map and one rule. For the alloy picture across nickel, titanium and zirconium, see our materials materials coverage; if you also run nickel, our nickel hub explains the family.
| Form / property | Zirconium vs Titanium | Note |
|---|---|---|
| HCl, all conc., boiling | Zirconium: excellent | Headline advantage over Ti/Ni |
| HCl + trace oxidiser (Fe³⁺, HNO3) | Zirconium: watch / verify per case | May need Zr705 or Hastelloy |
| HCl vapour, hot | Zirconium: OK | Use in condensers / stacks |
| HCl + fluoride | Zirconium: fails | Use Monel / nickel |
| HCl + wet chlorine | Zirconium: OK | Zr resists wet Cl2 |
| Max temp in reducing HCl | ~250°C (pressure-dependent) | Above ~540°C in air: no |
| Vs tantalum | Zr cheaper, nearly as resistant | Ta only where Zr envelope exceeded |
HCl is the “killing acid” for most engineering metals, but zirconium’s zirconia (ZrO₂) film is stable exactly in reducing HCl. The film reforms instantly if scratched, so zirconium keeps resisting instead of pitting. That is why it is specified for boiling HCl where titanium is attacked and 316L dissolves. We treat HCl service as a system — plate, tube and fittings planned from one grade so the whole loop stays in spec.
| Grade | Composition | Use it for |
|---|---|---|
| Zr702 (R60702) | ~99.2% Zr+Hf, low O | Boiling HCl; max formability, lowest cost |
| Zr705 (R60705) | +2.5% Nb | Same HCl resistance, ~50% higher strength |
| 702 vs 705 in HCl | Both fully resistant | 705 for thinner wall / higher pressure |
| Cross-check | — | See zirconium vs titanium for the metal choice |
For the full material picture — zirconium, titanium and nickel side by side — see our alloy matrix matrix. If the service is reducing acid but milder, our titanium titanium guide explains the cheaper option.
A usable quote starts with a usable request. Put these on the enquiry so we return price and lead time instead of questions:
| Form | Typical size | Where it goes |
|---|---|---|
| Plate / sheet | Thk 0.5–50 mm | Reactor shells, tube sheets, trays |
| Tube / pipe | OD 6–219 mm | HCl-recovery bundles, transfer lines |
| Bar / rod | Dia 6–300 mm | Spargers, agitators, shafts |
| Fittings / flange | per B16.5 / B16.9 | Branch, turn, termination of the loop |
Each lot ships with an EN 10204 3.1 mill test certificate, heat-number traceable to the melt, to ASTM B551/B523/B658 as applicable. Condition is annealed per spec; PMI, UT or dye-penetrant can be added on the order. For fabrications we kit the matching fittings and flange from one shipment.
Zirconium is not an acid-proof metal for every acid — hydrofluoric acid and fluorides destroy it, and it is not for concentrated hot caustic or strong oxidisers. For those services step to Monel / nickel or Hastelloy. Zirconium owns reducing HCl; match the grade to the actual fluid.
Zirconium’s strength is its reducing-acid film; its limits sit exactly where that film breaks down. Read the failure map, then the joint notes.
| Medium / condition | Titanium | Zirconium |
|---|---|---|
| HF / fluoride in the acid | Rapid attack — zirconium fails completely | Use Monel 400 / pure nickel |
| Strong oxidiser added (fuming HNO3, free Cl2 + oxidiser) | Film breaks, attack begins | Step to Hastelloy C-276 / C-22 |
| Temperature >~250°C in reducing HCl under pressure | Check per case; envelope narrows | Verify with MTC and service data |
| Air / oxidising gas above ~540°C | Oxidises and can burn reactively | Zirconium is not a high-temp alloy |
| Molten salts / heavy-metal contamination | Embrittle or attack | Keep zirconium out of such contact |
| Galvanic with a much baser metal in HCl | Base partner corrodes fast | Dielectric spacer if critical |
Two joint-specific notes. Zirconium is noble when passive, so coupling it directly to a much baser metal without isolation can accelerate the partner — use a dielectric spacer where the partner is critical. And never forget fluorine: any fluoride, even trace, is an exclusion, so confirm the medium is fluoride-free before you specify zirconium.
Choose this if:
Choose that if:
Zirconium and titanium are held in Baoji across plate, tube, bar, wire, fittings and flange, cut to size and dispatched fast for standard sizes. Heavy-wall tube, large forged flange or special tempers lead a few weeks. Small MOQ applies — a single plate, one spool or a set of flanges is a normal order, and we kit the whole line from one shipment with one certificate pack.
| If the service is… | Then… |
|---|---|
| Tantalum | Excellent in HCl but 5–10× zirconium’s cost — use Ta only where Zr envelope is exceeded. |
| Titanium (Gr2 / Gr7) | Attacked by HCl — wrong metal for boiling HCl; use zirconium. |
| 316L / nickel alloys | Dissolve or fail in HCl — wrong for HCl; use zirconium. |
| Glass-lined steel | Limited temperature and prone to thermal-shock cracking — zirconium is more robust. |
| Hastelloy C-276 / C-22 | Resists but costs more than zirconium for pure HCl; use when an oxidiser is also present. |
Zirconium in HCl service welds readily but is unforgiving: any oxygen or surface contamination during welding produces a hard, brittle, badly corroding joint. Use matching zirconium filler and a qualified WPS with argon backing gas on BOTH the inside and outside of tube and pipe, and keep the joint and wire clean. We supply the matching wire and forming notes — a contaminated zirconium weld is the single most common field failure, so do not skip the purge.
Every lot ships with an EN 10204 3.1 EN 10204 3.1 MTC: grade and UNS, heat number, chemistry (including hafnium, which affects nuclear grade), tensile result, and the ASTM specification. Keep the heat number — it is your traceability link from the finished part back to the melt, and it is what lets an auditor confirm the grade years later.
We hold zirconium together with titanium and nickel in Baoji, close to China’s Titanium Valley supply base, which means we can cut, forge and kit an HCl loop from one shipment instead of chasing several mills. That shortens lead time from mill-weeks to days and keeps one grade logic, one certificate pack, and one point of contact. Our guide explains the stock-holder model for overseas buyers.
Copy this into your enquiry and fill the blanks — it returns a quote, not a guessing game:
Email it to [email protected] — we confirm stock and pricing within 24 hours, and can kit the whole line from one Baoji shipment so grade and certificate stay consistent end to end.
Yes — zirconium resists hydrochloric acid at every concentration and to the boiling point, which is its headline advantage over titanium and most nickel alloys. The one acid it cannot take is hydrofluoric acid.
Both are fully resistant in HCl. Zr705 adds about 2.5% niobium for roughly 50% higher strength, so pick it for thinner walls or higher pressure; Zr702 for maximum formability and lowest cost.
Zirconium is the standard metal for HCl recovery and regeneration equipment — pickling-line acid recovery, spargers, reheaters, crystallisers — because it survives boiling HCl for years where alternatives fail.
Yes — hydrofluoric acid and fluorides destroy it; concentrated hot caustic and strong oxidisers attack it; and it is not a high-temperature alloy above ~540°C in air. For those, step to Monel, nickel, Hastelloy or Inconel.
Both resist HCl, but zirconium costs a fraction of tantalum. Use tantalum only where zirconium’s temperature or pressure envelope is exceeded; for most boiling HCl, zirconium is the economical choice.
GTAW with matching zirconium filler and argon backing gas on both sides of the joint; any contamination makes the weld brittle and corrosive. We supply the matching wire and a qualified WPS note.
Yes. Baoji stock to global ports with VCI protection, crating and full EN 10204 3.1 MTC and shipping documents.
If you take one thing from this guide, take this: specify the metal for the fluid, not just the word “corrosion-resistant,” and treat every joint as a system. Zirconium in Hydrochloric Acid & HCl Recovery Units is the right call for boiling reducing acids — and never specify it where the failure map says no. Send the checklist above to [email protected] or use the inquiry form — we confirm stock and pricing within 24 hours, and can kit the whole line from one Baoji shipment.
Tell us your requirement — grade, size and quantity. We reply within 24 hours.
Prefer chat? WhatsApp +86 188 2967 9311 or email [email protected].
Contact Person: Wang Xiaoning
Tel: +86-917-355-7966
Email: [email protected]
WhatsApp: +86 188 2967 9311
Company: Shaanxi Qianyi Tuoda Technology Co., Ltd
Address: Floor 4, Building 4, No. 188 Gaoxin Avenue, High-tech Zone, Baoji City, Shaanxi Province, China